Skip to content
410 Premium Non-Fibrated Aluminum Roof Coating

410 Premium Non-Fibrated Aluminum Roof Coating

Mule-Hide #410 Premium Non-Fibrated Aluminum Roof Coating provides premium, high-performance protection for asphalt-based roofs. Mule-Hide #410 Premium Non-Fibrated Aluminum Roof Coating is easier to spread and provides greater coverage. This formula is non-destructive to asphalt based roofing membranes. Formula produced with premium amounts of aluminum pigment per gallon for maximum reflectivity.

System

ModBit
M&R
  • Can be used to coat a variety of other substrates including masonry surfaces, and structural steel
  • Apply product only in areas with positive drainage
  • Designed for application over new or existing APP or SBS, smooth or granulated surface, cap sheet, asphalt built-up roofs and flashings
  • DO NOT USE with PVC, TPO, EPDM or other single-ply membranes
  • A bright silver finish that reflects heat and UV rays
  • Product must be mixed very well with a power drill until coating appears silver. Hand mixing is not satisfactory. Average mix time per bucket should be approximately 2 minutes
  • Meets Miami-Dade-County Standards

Documents

PDS 410 Premium Non-Fibrated Aluminum Roof Coating
View
SDS 410 Premium Non-Fibrated Aluminum Roof Coating
View

Florida Product Approval - Cements, Adhesives, Coatings
View
Miami-Dade NOA - Asphalt Products NOA
View

Adhesion Test Step-by-Step
View
Asphalt Cements & Coatings Cross Reference Chart
View
Maintenance & Repair Brochure
View
Sell Sheet - 410 Premium Non-Fibrated Aluminum Roof Coating
View

Options

Item ID Description Packaging Qty per Ctn Weight per Ctn Cover Rate
16MH4105 MH 410 PREMIUM NON-FIBRATED ALUM 5 GAL Metal Pail 1 45 1-1.5 gallons per 100 sq. ft.
16MH41050 MH 410 PREMIUM NON-FIBRATED ALUM 55 GAL Drum 1 444 1-1.5 gallons per 100 sq. ft.

FAQs

For contractors seeking greater brightness, reflectivity, and brilliance, the Mule-Hide #410 Premium Non-Fibrated Aluminum Roof Coating offers greater brilliance than the #416 Standard Non-Fibrated Aluminum Roof Coating. When optics and aesthetics are paramount, the #410 Premium is the coating of choice.

The coverage rate for Mule-Hide #410 Premium Non-Fibrated Aluminum Roof Coating is approximately 1 to 1.5 gallons per 100 sq. ft. The spray requirements are 3,000 psi at 1.5 gallons per minute. Tip size = 0.051 to 0.067, Fan = 6 inches. (All values are approximate and may vary with ambient temperature and job conditions.)

Mule-Hide #410 Premium Non-Fibrated Aluminum Roof Coating can be applied using a high-pressure sprayer, a roller, or a brush. For best results, spray using proper equipment.

NO. DO NOT apply Mule-Hide #410 Premium Non-Fibrated Aluminum Roof Coating to PVC, TPO, EPDM or other single-ply roofing membranes.

With proper storage, the shelf life of Mule-Hide #410 Premium Non-Fibrated Aluminum Roof Coating is 24 months from the date of manufacture.

Mule-Hide #410 Premium Non-Fibrated Aluminum Roof Coating should be stored at a temperature of at least 45° F but not above 120° F. It should be stored at room temperature for at least 24 hours prior to use.

Mule-Hide #410 Premium Non-Fibrated Aluminum Roof Coating should only be applied when the ambient temperature is at least 50° F and rising. Cold weather can result in uneven application and improper curing, and it will cause the product to stiffen, making application more difficult. Do not apply Mule-Hide #401 Premium Fibrated Aluminum Roof Coating if there is a threat of inclement weather within 24 hours of application.